141 lines
5.5 KiB
C
141 lines
5.5 KiB
C
// Copyright (c) 2022 Cesanta Software Limited
|
|
// All rights reserved
|
|
// https://www.st.com/resource/en/reference_manual/dm00031020-stm32f405-415-stm32f407-417-stm32f427-437-and-stm32f429-439-advanced-arm-based-32-bit-mcus-stmicroelectronics.pdf
|
|
|
|
#pragma once
|
|
|
|
#include <stm32f429xx.h>
|
|
|
|
#include <stdbool.h>
|
|
#include <stdint.h>
|
|
#include <stdio.h>
|
|
#include <string.h>
|
|
|
|
#define BIT(x) (1UL << (x))
|
|
#define SETBITS(R, CLEARMASK, SETMASK) (R) = ((R) & ~(CLEARMASK)) | (SETMASK)
|
|
#define PIN(bank, num) ((((bank) - 'A') << 8) | (num))
|
|
#define PINNO(pin) (pin & 255)
|
|
#define PINBANK(pin) (pin >> 8)
|
|
|
|
// 6.3.3: APB1 clock <= 45MHz; APB2 clock <= 90MHz
|
|
// 3.5.1, Table 11: configure flash latency (WS) in accordance to clock freq
|
|
// 33.4: The AHB clock must be at least 25 MHz when Ethernet is used
|
|
enum { APB1_PRE = 5 /* AHB clock / 4 */, APB2_PRE = 4 /* AHB clock / 2 */ };
|
|
enum { PLL_HSI = 16, PLL_M = 8, PLL_N = 168, PLL_P = 2, PLL_Q = 7 };
|
|
#define FLASH_LATENCY 5
|
|
#define SYS_FREQUENCY ((PLL_HSI * PLL_N / PLL_M / PLL_P) * 1000000) // Core 168 MHz, USB 48 MHz
|
|
#define APB2_FREQUENCY (SYS_FREQUENCY / (BIT(APB2_PRE - 3)))
|
|
#define APB1_FREQUENCY (SYS_FREQUENCY / (BIT(APB1_PRE - 3)))
|
|
|
|
static inline void spin(volatile uint32_t count) {
|
|
while (count--) (void) 0;
|
|
}
|
|
|
|
enum { GPIO_MODE_INPUT, GPIO_MODE_OUTPUT, GPIO_MODE_AF, GPIO_MODE_ANALOG };
|
|
enum { GPIO_OTYPE_PUSH_PULL, GPIO_OTYPE_OPEN_DRAIN };
|
|
enum { GPIO_SPEED_LOW, GPIO_SPEED_MEDIUM, GPIO_SPEED_HIGH, GPIO_SPEED_INSANE };
|
|
enum { GPIO_PULL_NONE, GPIO_PULL_UP, GPIO_PULL_DOWN };
|
|
#define GPIO(N) ((GPIO_TypeDef *) (0x40020000 + 0x400 * (N)))
|
|
|
|
static GPIO_TypeDef *gpio_bank(uint16_t pin) { return GPIO(PINBANK(pin)); }
|
|
static inline void gpio_toggle(uint16_t pin) {
|
|
GPIO_TypeDef *gpio = gpio_bank(pin);
|
|
uint32_t mask = BIT(PINNO(pin));
|
|
gpio->BSRR = mask << (gpio->ODR & mask ? 16 : 0);
|
|
}
|
|
static inline int gpio_read(uint16_t pin) {
|
|
return gpio_bank(pin)->IDR & BIT(PINNO(pin)) ? 1 : 0;
|
|
}
|
|
static inline void gpio_write(uint16_t pin, bool val) {
|
|
GPIO_TypeDef *gpio = gpio_bank(pin);
|
|
gpio->BSRR = BIT(PINNO(pin)) << (val ? 0 : 16);
|
|
}
|
|
static inline void gpio_init(uint16_t pin, uint8_t mode, uint8_t type,
|
|
uint8_t speed, uint8_t pull, uint8_t af) {
|
|
GPIO_TypeDef *gpio = gpio_bank(pin);
|
|
uint8_t n = (uint8_t) (PINNO(pin));
|
|
RCC->AHB1ENR |= BIT(PINBANK(pin)); // Enable GPIO clock
|
|
SETBITS(gpio->OTYPER, 1UL << n, ((uint32_t) type) << n);
|
|
SETBITS(gpio->OSPEEDR, 3UL << (n * 2), ((uint32_t) speed) << (n * 2));
|
|
SETBITS(gpio->PUPDR, 3UL << (n * 2), ((uint32_t) pull) << (n * 2));
|
|
SETBITS(gpio->AFR[n >> 3], 15UL << ((n & 7) * 4),
|
|
((uint32_t) af) << ((n & 7) * 4));
|
|
SETBITS(gpio->MODER, 3UL << (n * 2), ((uint32_t) mode) << (n * 2));
|
|
}
|
|
static inline void gpio_input(uint16_t pin) {
|
|
gpio_init(pin, GPIO_MODE_INPUT, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH,
|
|
GPIO_PULL_NONE, 0);
|
|
}
|
|
static inline void gpio_output(uint16_t pin) {
|
|
gpio_init(pin, GPIO_MODE_OUTPUT, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH,
|
|
GPIO_PULL_NONE, 0);
|
|
}
|
|
|
|
static inline void irq_exti_attach(uint16_t pin) {
|
|
uint8_t bank = (uint8_t) (PINBANK(pin)), n = (uint8_t) (PINNO(pin));
|
|
SYSCFG->EXTICR[n / 4] &= ~(15UL << ((n % 4) * 4));
|
|
SYSCFG->EXTICR[n / 4] |= (uint32_t) (bank << ((n % 4) * 4));
|
|
EXTI->IMR |= BIT(n);
|
|
EXTI->RTSR |= BIT(n);
|
|
EXTI->FTSR |= BIT(n);
|
|
int irqvec = n < 5 ? 6 + n : n < 10 ? 23 : 40; // IRQ vector index, 10.1.2
|
|
NVIC_SetPriority(irqvec, 3);
|
|
NVIC_EnableIRQ(irqvec);
|
|
}
|
|
|
|
#ifndef UART_DEBUG
|
|
#define UART_DEBUG USART3
|
|
#endif
|
|
|
|
static inline void uart_init(USART_TypeDef *uart, unsigned long baud) {
|
|
// https://www.st.com/resource/en/datasheet/stm32f429zi.pdf
|
|
uint8_t af = 7; // Alternate function
|
|
uint16_t rx = 0, tx = 0; // pins
|
|
uint32_t freq = 0; // Bus frequency. UART1 is on APB2, rest on APB1
|
|
|
|
if (uart == USART1) freq = APB2_FREQUENCY, RCC->APB2ENR |= BIT(4);
|
|
if (uart == USART2) freq = APB1_FREQUENCY, RCC->APB1ENR |= BIT(17);
|
|
if (uart == USART3) freq = APB1_FREQUENCY, RCC->APB1ENR |= BIT(18);
|
|
|
|
if (uart == USART1) tx = PIN('A', 9), rx = PIN('A', 10);
|
|
if (uart == USART2) tx = PIN('A', 2), rx = PIN('A', 3);
|
|
if (uart == USART3) tx = PIN('D', 8), rx = PIN('D', 9);
|
|
|
|
gpio_init(tx, GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, 0, af);
|
|
gpio_init(rx, GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH, 0, af);
|
|
uart->CR1 = 0; // Disable this UART
|
|
uart->BRR = freq / baud; // Set baud rate
|
|
uart->CR1 |= BIT(13) | BIT(2) | BIT(3); // Set UE, RE, TE
|
|
}
|
|
static inline void uart_write_byte(USART_TypeDef *uart, uint8_t byte) {
|
|
uart->DR = byte;
|
|
while ((uart->SR & BIT(7)) == 0) spin(1);
|
|
}
|
|
static inline void uart_write_buf(USART_TypeDef *uart, char *buf, size_t len) {
|
|
while (len-- > 0) uart_write_byte(uart, *(uint8_t *) buf++);
|
|
}
|
|
static inline int uart_read_ready(USART_TypeDef *uart) {
|
|
return uart->SR & BIT(5); // If RXNE bit is set, data is ready
|
|
}
|
|
static inline uint8_t uart_read_byte(USART_TypeDef *uart) {
|
|
return (uint8_t) (uart->DR & 255);
|
|
}
|
|
|
|
static inline void rng_init(void) {
|
|
RCC->AHB2ENR |= RCC_AHB2ENR_RNGEN;
|
|
RNG->CR |= RNG_CR_RNGEN;
|
|
}
|
|
static inline uint32_t rng_read(void) {
|
|
while ((RNG->SR & RNG_SR_DRDY) == 0) (void) 0;
|
|
return RNG->DR;
|
|
}
|
|
|
|
#define UUID ((uint8_t *) UID_BASE) // Unique 96-bit chip ID. TRM 39.1
|
|
|
|
// Helper macro for MAC generation
|
|
#define GENERATE_LOCALLY_ADMINISTERED_MAC() \
|
|
{ \
|
|
2, UUID[0] ^ UUID[1], UUID[2] ^ UUID[3], UUID[4] ^ UUID[5], \
|
|
UUID[6] ^ UUID[7] ^ UUID[8], UUID[9] ^ UUID[10] ^ UUID[11] \
|
|
}
|