// Copyright (c) 2022-2023 Cesanta Software Limited
// All rights reserved

#include "hal.h"
#include "mongoose.h"

#define LED1 PIN('B', 0)   // On-board LED pin (green)
#define LED2 PIN('B', 7)   // On-board LED pin (blue)
#define LED3 PIN('B', 14)  // On-board LED pin (red)

#define LED LED2              // Use blue LED for blinking
#define BLINK_PERIOD_MS 1000  // LED blinking period in millis

static volatile uint64_t s_ticks;  // Milliseconds since boot
void SysTick_Handler(void) {       // SyStick IRQ handler, triggered every 1ms
  s_ticks++;
}

uint64_t mg_millis(void) {  // Let Mongoose use our uptime function
  return s_ticks;           // Return number of milliseconds since boot
}

void mg_random(void *buf, size_t len) {  // Use on-board RNG
  for (size_t n = 0; n < len; n += sizeof(uint32_t)) {
    uint32_t r = rng_read();
    memcpy((char *) buf + n, &r, n + sizeof(r) > len ? len - n : sizeof(r));
  }
}

static void timer_fn(void *arg) {
  gpio_toggle(LED);                               // Blink LED
  struct mg_tcpip_if *ifp = arg;                  // And show
  const char *names[] = {"down", "up", "ready"};  // network stats
  MG_INFO(("Ethernet: %s, IP: %M, rx:%u, tx:%u, dr:%u, er:%u",
           names[ifp->state], mg_print_ip4, &ifp->ip, ifp->nrecv, ifp->nsent,
           ifp->ndrop, ifp->nerr));
}

static void ethernet_init(void) {
  // Initialise Ethernet. Enable MAC GPIO pins, see
  // https://www.farnell.com/datasheets/2014265.pdf section 6.10
  uint16_t pins[] = {PIN('A', 1),  PIN('A', 2),  PIN('A', 7),
                     PIN('B', 13), PIN('C', 1),  PIN('C', 4),
                     PIN('C', 5),  PIN('G', 11), PIN('G', 13)};
  for (size_t i = 0; i < sizeof(pins) / sizeof(pins[0]); i++) {
    gpio_init(pins[i], GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_INSANE,
              GPIO_PULL_NONE, 11);  // 11 is the Ethernet function
  }
  NVIC_EnableIRQ(ETH_IRQn);                // Setup Ethernet IRQ handler
  SYSCFG->PMC |= SYSCFG_PMC_MII_RMII_SEL;  // Use RMII. Goes first!
  RCC->AHB1ENR |=
      RCC_AHB1ENR_ETHMACEN | RCC_AHB1ENR_ETHMACTXEN | RCC_AHB1ENR_ETHMACRXEN;
}

int main(void) {
  gpio_output(LED);               // Setup green LED
  uart_init(UART_DEBUG, 115200);  // Initialise debug printf
  ethernet_init();                // Initialise ethernet pins
  MG_INFO(("Starting, CPU freq %g MHz", (double) SystemCoreClock / 1000000));

  struct mg_mgr mgr;        // Initialise
  mg_mgr_init(&mgr);        // Mongoose event manager
  mg_log_set(MG_LL_DEBUG);  // Set log level

  // Initialise Mongoose network stack
  // Specify MAC address, and IP/mask/GW in network byte order for static
  // IP configuration. If IP/mask/GW are unset, DHCP is going to be used
  struct mg_tcpip_driver_stm32_data driver_data = {.mdc_cr = 4};
  struct mg_tcpip_if mif = {.mac = GENERATE_LOCALLY_ADMINISTERED_MAC(),
                            .driver = &mg_tcpip_driver_stm32,
                            .driver_data = &driver_data};
  mg_tcpip_init(&mgr, &mif);
  mg_timer_add(&mgr, BLINK_PERIOD_MS, MG_TIMER_REPEAT, timer_fn, &mif);

  MG_INFO(("MAC: %M. Waiting for IP...", mg_print_mac, mif.mac));
  while (mif.state != MG_TCPIP_STATE_READY) {
    mg_mgr_poll(&mgr, 0);
  }

  MG_INFO(("Initialising application..."));
  extern void device_dashboard_fn(struct mg_connection *, int, void *, void *);
  mg_http_listen(&mgr, "http://0.0.0.0", device_dashboard_fn, NULL);

  MG_INFO(("Starting event loop"));
  for (;;) {
    mg_mgr_poll(&mgr, 0);
  }

  return 0;
}