iw4x-client/deps/mongoose/examples/ti/ek-tm4c1294xl-baremetal/main.c

// Copyright (c) 2022-2023 Cesanta Software Limited
// All rights reserved

#include "hal.h"
#include "mongoose.h"

#define LED1 PIN('N', 1)  // On-board LED pin
#define LED2 PIN('N', 0)  // On-board LED pin
#define LED3 PIN('F', 4)  // On-board LED pin
#define LED4 PIN('F', 0)  // On-board LED pin

#define LED LED1              // Use this LED for blinking
#define BLINK_PERIOD_MS 1000  // LED blinking period in millis

static volatile uint64_t s_ticks;  // Milliseconds since boot
void SysTick_Handler(void) {       // SyStick IRQ handler, triggered every 1ms
  s_ticks++;
}

uint64_t mg_millis(void) {  // Let Mongoose use our uptime function
  return s_ticks;           // Return number of milliseconds since boot
}

static void timer_fn(void *arg) {
  gpio_toggle(LED);                               // Blink LED
  struct mg_tcpip_if *ifp = arg;                  // And show
  const char *names[] = {"down", "up", "ready"};  // network stats
  MG_INFO(("Ethernet: %s, IP: %M, rx:%u, tx:%u, dr:%u, er:%u",
           names[ifp->state], mg_print_ip4, &ifp->ip, ifp->nrecv, ifp->nsent,
           ifp->ndrop, ifp->nerr));
}

static void ethernet_init(void) {
  // Initialise Ethernet. Enable MAC GPIO pins, see
  // https://www.ti.com/lit/pdf/spms433
  // Assign LED3 and LED4 to the EPHY, "activity" and "link", respectively.
  // (20.4.2.4)
  gpio_init(LED3, GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH,
            GPIO_PULL_NONE, 5);  // EN0LED1
  gpio_init(LED4, GPIO_MODE_AF, GPIO_OTYPE_PUSH_PULL, GPIO_SPEED_HIGH,
            GPIO_PULL_NONE, 5);  // EN0LED0
  NVIC_EnableIRQ(EMAC0_IRQn);    // Setup Ethernet IRQ handler
  // Initialize Ethernet clocks, see datasheet section 5
  // Turn Flash Prefetch off (silicon errata ETH#02)
  uint32_t val = FLASH_CTRL->CONF;
  val &= ~BIT(17);
  val |= BIT(16);
  FLASH_CTRL->CONF = val;
  SYSCTL->RCGCEMAC |= BIT(0);  // Enable EMAC clock
  SYSCTL->SREMAC |= BIT(0);    // Reset EMAC
  SYSCTL->SREMAC &= ~BIT(0);
  SYSCTL->RCGCEPHY |= BIT(0);  // Enable EPHY clock
  SYSCTL->SREPHY |= BIT(0);    // Reset EPHY
  SYSCTL->SREPHY &= ~BIT(0);
  while (!(SYSCTL->PREMAC & BIT(0)) || !(SYSCTL->PREPHY & BIT(0)))
    spin(1);  // Wait for reset to complete
}

int main(void) {
  gpio_output(LED);               // Setup leftmost LED
  uart_init(UART_DEBUG, 115200);  // Initialise debug printf
  ethernet_init();                // Initialise ethernet pins
  MG_INFO(("Starting, CPU freq %g MHz", (double) SystemCoreClock / 1000000));

  struct mg_mgr mgr;        // Initialise
  mg_mgr_init(&mgr);        // Mongoose event manager
  mg_log_set(MG_LL_DEBUG);  // Set log level

  // Initialise Mongoose network stack
  // Specify MAC address, and IP/mask/GW in network byte order for static
  // IP configuration. If IP/mask/GW are unset, DHCP is going to be used
  struct mg_tcpip_driver_tm4c_data driver_data = {.mdc_cr =
                                                      1};  // See driver_tm4c.h
  struct mg_tcpip_if mif = {
      .mac = READ_PREFLASHED_MAC(),
      .driver = &mg_tcpip_driver_tm4c,
      .driver_data = &driver_data,
  };
  mg_tcpip_init(&mgr, &mif);
  uint32_t val = FLASH_CTRL->CONF;  // Turn Flash Prefetch on again
  val &= ~BIT(16);
  val |= BIT(17);
  FLASH_CTRL->CONF = val;
  mg_timer_add(&mgr, BLINK_PERIOD_MS, MG_TIMER_REPEAT, timer_fn, &mif);

  MG_INFO(("MAC: %M. Waiting for IP...", mg_print_mac, mif.mac));
  while (mif.state != MG_TCPIP_STATE_READY) {
    mg_mgr_poll(&mgr, 0);
  }

  MG_INFO(("Initialising application..."));
  extern void device_dashboard_fn(struct mg_connection *, int, void *, void *);
  mg_http_listen(&mgr, "http://0.0.0.0", device_dashboard_fn, NULL);

  MG_INFO(("Starting event loop"));
  for (;;) {
    mg_mgr_poll(&mgr, 0);
  }

  return 0;
}